8 ultra precision thin film chip resistors l w t 1 2 2 1 resistive film (ni-cr-si) environmental seal high purity alumina termination finish is 100% matte tin (sn) over nickel (ni) uptf0805-10w ? p ? xxxx a t series tcr p: 5ppm/ c n: 10ppm/ c e: 25ppm/ c resistance value resistance tolerance u: 0.01% a: 0.05% b: 0.1% c: 0.25% d: 0.5% f: 1% packaging t: tape ? minimized aging ? tcr as low as 5 ppm /c and tolerance as low as 0.01% ? good high frequency characteristics ? suitable for flow and reflow soldering features dimensions specifications how to order unit: inches (mm) 5900 shepherd mountain cove ? austin, tx 78730 phone: 512 / 794-0081 ? fax: 512 / 794-0087 ? toll free: 800 / 950-8365 e-mail: sales@venkel.com ? www.venkel.com * please consult your salesperson for values available outside this range and for non-standard values. ** please see tfcr series for maximum working and overload voltage specifications on page 46. all components in this section are rohs compliant per the eu directives and definitions. standard termination finish for this product is 100% matte tin (sn) uptf00 uptf060 uptf0805 uptf06 l 0.040 .002 (1.0 0.05) 0.063 .008 (1.6 0.2) 0.079 .008 (2.0 0.2) 0.126 .008 (3.2 0.2) w 0.020 .002 (0.5 0.05) 0.031 .008 (0.8 0.2) 0.050 .008 (1.25 0.02) 0.063 .008 (1.6 0.2) t 0.014 .002 (0.35 0.05) 0.018 .004 (0.45 0.10) 0.020 .006 (0.50 0.15) 0.022 .006 (0.57 0.15) 1 0.008 .004 (0.2 0.01) 0.010 .006 (0.25 0.15) 0.016 .008 (0.4 0.2) 0.018 .008 (0.45 0.2) 2 0.008 .004 (0.2 0.01) 0.010 .006 (0.25 0.15) 0.012 .008 (0.3 0.2) 0.012 .008 (0.3 0.2) series power rating at 70?c (w) resistance range specifc resistance range* tolerance available temperature coeffcient of resistance (0 -6 /?c ppm) operating temperature range (?c) uptf0402 0.063 10 w - 100k w 100 w - 3k w (>.05%) u, a, b, c, d, f 10 C55 ~ +150 10 w - 100k w u, a, b, c, d, f 25 uptf0603 0.063 10 w - 150k w 10 w - 50k w (>.05%) u, a, b, c, d, f 5, 10 C55 ~ +150 0.10 10 w - 150k w u, a, b, c, d, f 25 uptf0805 0.10 10 w - 500k w 10 w - 150k w (>.05%) u, a, b, c, d, f 5, 10 C55 ~ +150 0.125 10 w - 500k w u, a, b, c, d, f 25 uptf1206 0.125 10 w - 500k w 10 w - 470k w (>.05%) u, a, b, c, d, f 5, 10 C55 ~ +150 0.25 10 w - 500k w u, a, b, c, d, f 25
5900 shepherd mountain cove ? austin, tx 78730 phone: 512 / 794-0081 ? fax: 512 / 794-0087 ? toll free: 800 / 950-8365 e-mail: sales@venkel.com ? www.venkel.com 9 description requirements test method jis c 5 0 short-time overload within (0.1% +0.05 w ) 2.5 times rated voltage no major visible damage 5 seconds insulation resistance at least 1,000 m w 100v 1 minute withstanding voltage within (0.5% +0.05 w ) 1/10: ac 150v 1 minute no flashover, scorching 1/8: ac 300v 1 minute or insulation breakdown terminal strength within (0.5% +0.05 w ) install a sample on the board no mechanical damage and bend the board 3/45mm for 10 seconds solder heat resistance within (0.05% +0.05 w ) dip into 260c solder bath no major visible damage for 10 seconds solderability at least 95% of the dipping 235c 2 seconds surface must be covered by new solder temperature cycle within (0.1% +0.05 w ) cycle between -55c and no major visible damage + 150c for 5 cycles markings legible load life in moisture within (0.25% +0.05 w ) rated voltage 1.5 hours no major visible damage on 0.5 hours off markings legible 40c, 95% rh 1,000 hours load life within (0.25% +0.05 w ) rated voltage 1.5 hours no major visible damage on 0.5 hours off markings legible 70c 1,000 hours c haracteristics part marking description derating curve rated power (%) ambient temperature ( c) 100 80 60 40 20 0 -55 0 7 0 1 25 15 0 note: these specifications are typical and are based on standard operating conditions. ? if the component is a crossover value (both available in e-24 and e-96) then the 3 digit e-24 series marking will typically be used. ? 0402 size resistors are not marked. series e values e96 values uptf0603 standard 3 digit marking alpha code system (alpha numeric code - see pg. 60) uptf0805 standard 3 digit marking standard 4 digit marking uptf1206 standard 3 digit marking standard 4 digit marking examples: 3 digit (alpha numeric) 30c = 20k w standard 3 digit 103 = 10k w standard 4 digit 2491 = 2.49k w
|
